Edge-lighting Cirrus Channel, Direct 1" Lens Instrukcja Użytkownika Pobierz pdf

Installation Instructions for Cirrus Channel, Direct 1" Lens, 24VDC

904-CC-D1-02

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: 773-770-1195

Fax: 773-935-5613

www.edgelighting.com

[email protected]

CC-D1-2WDC-_

CC-D1-5WDC-_

JOINER BRACKET

CHANNEL

LENS

1: Lift a section of the lens at the end of the channels where

the connectors are visible. Slide the channel over the joiner

bracket make sure that the male & female connectors mate

properly.

2: Push the lens back into the channel.

NOTE:

piece (120" or less).

Omit this section if the channel is made out of a single

NOTE: Prior to installation, multi-sectional Cirrus Channel should

be connected together for marking proper measurements.

NOTE: It is recommended more than one person to assist in this

installation.

Connecting the Channel

JOINER CHANNEL

MALE

CONNECTOR

FEMALE

CONNECTOR

CHANNEL

FRONT

VIEW

TOP OF CHANNEL

Install Channel on Standard Junction Box W/Plaster Ring or Octagon Box

NOTE:

(C-1RE-BOX), continue to "Install the Channel using the Junction

Box (C-1RE-JBOX)" on page 3.

When using Edge Lighting Slim Profile Junction Box

1: Mount the crossbar to the Junction box holes with the two

#8-32 screws provided.

#8-32 SCREW

CROSSBAR

JUNCTION BOX

CHANNEL END

BOTTOM OF CHANNEL

JUNCTION BOX

MOUNTING

CLIP (C-MCL)

RECEIVING BRACKET

MARKING LOCATION

LOCKING CLIP

NOTE: Remote power supply must be installed within 40ft of

Junction box. The low voltage 24V DC wires must be present in

Junction box before installing the channel. Refer to the

installation instructions provided with the power supply. See

page 5 for wiring diagram.

NOTE: If the receiving bracket interferes with the Junction box

or wires, then relocate the receiving bracket by loosening the

screws and make the necessary adjustments.

NOTE: The channel must pass through the center of the

Junction box.

EVERY 20 INCHES

2: Begin installation using side of the channel with power wire.

Lay channel to the desired location & make all necessary

markings which will consist of the channel ends, locking clips

and mounting clips. Mounting clips must be installed 20"

from each other. Locking clips are not necessary for

channels under 2ft.

3: After all markings and required measurements are done,

take the channels apart from each other.

SAVE THESE INSTRUCTIONS!

- This instruction shows a typical installation.

- Per NEC Article 410.16(A)(1)(3) & 410.16(C)(5). Approved

for Closet Storage Areas.

IMPORTANT INFORMATION

LOCKING CLIP

NOTE:

C-1RE-JBOX.

Omit this section and follow steps on Page 3 when using

1 2 3 4 5

Podsumowanie treści

Strona 1 - Connecting the Channel

Installation Instructions for Cirrus Channel, Direct 1" Lens, 24VDC 904-CC-D1-021718 W. Fullerton AveChicago, IL 60614Tel: 773-770-1195Fax: 773-9

Strona 2

2DSURFACENOTE:if mounting the clips to a wood surface directly. Steps 3 and 4 are for drywall mounting. Omit these steps 4: Tap the anchors onto the m

Strona 3

3H12: Place each canopy piece against the channel & line up the canopy hole with the crossbar hole. Secure the canopy in place with th

Strona 4

JUNCTION BOX OPENINGNOTE: If the receiving bracket interferes with the Junction box, then relocate the bracket by loosening the set screws and make t

Strona 5 - CIRRUS CHANNEL

5PMOUNTING CLIP (C-MCL)WIRE MANAGEMENTCLIPCORDCHANNEL16141514: Connect the red power supply (24VDC+) wire to red strip wire with a wire nut insi

Komentarze do niniejszej Instrukcji

Brak uwag

Edge-lighting Cirrus Channel, Direct 1" Lens Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Oświetlenie Edge-lighting Cirrus Channel, Direct 1" Lens. Edge Lighting Cirrus Channel, Direct 1" Lens User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Oświetlenie Edge-lighting Cirrus Channel, Direct 1" Lens